Vertical-Cavity Surface-Emitting Lasers (VCSELs) are widely used for optical interconnects, 3D sensing like face recognition, or automotive applications. Conventional VCSELs with top/bottom distributed Bragg reflectors (DBRs) for any wavelength range are costly and bulky, needing precise growth control. High-contrast subwavelength gratings (HCGs) show a near 100% reflectivity across a wide wavelength range, and have a typical thickness of a few hundred nanometers, much thinner than epitaxial DBRs. In addition, HCGs were reported to have the ability to tightly confine the field in the HCG-based vertical cavities, very promising for high-speed devices. Thus HCGs are ideal candidates for mirror replacements, at least at the top, to construct vertical cavities. Currently HCGs are often based on an oxide layer, being monolithically integrated, or air-suspended, and the fabrication of these HCGs is still challenging.
VCSELs at 940 nm have been attracting particular attention for short-wave wavelength division multiplexing and sensing. Here we report for the first time electrically injected 940-nm HCG-VCSELs using post-supported air-suspended HCGs. The HCG-VCSELs are fabricated without critical point drying, and the HCGs can be released with a 100% yield in water or isopropanol. Our first generation HCG-VCSELs achieve already a low threshold current of 0.65 mA, and a large side-mode suppression ratio of 43.6 dB at 25 ℃ under continuous-wave operation. Theoretically, these HCG-VCSELs have a smaller effective mode length of 1.38*(λ/n), than that of conventional VCSELs with λ/2 cavities. The relaxation resonance frequency will increase by 16%. A data rate of 100 Gbps for these HCG-VCSELs is expected for the on-off keying modulation format.
Our present design and fabrication methods of the HCG-VCSELs can be extended to other wavelength ranges.
We experimentally demonstrate for the first time electrically-injected Vertical-Cavity Surface-Emitting Lasers (VCSELs) with post-supported high-contrast gratings (HCGs) at 940 nm. The HCG-VCSELs have two posts to support the air-suspended HCGs, being realized by simple fabrication without critical point drying. The HCGs can be released with a 100% yield in water or isopropanol. The HCG-VCSEL with a 4 μm × 8 μm oxide aperture achieves a low threshold current of 0.65 mA and a large side-mode suppression ratio of 43.6 dB under continuous-wave operation at 25 degrees. Theoretically, the relaxation resonance frequency of the HCG-VCSEL will increase by 16% compared with that of the conventional VCSEL with a λ/2 cavity. The data rate of 100 Gbps in the on-off keying modulation format for the HCG-VCSEL is expected.
Vertical-cavity surface-emitting lasers (VCSELs) have wide applications in data communication, sensing, and consumer electronics, because they have many advantages, such as circular beam, low power consumption, high modulation speed, low cost, high reliability, and 2D array configuration. Metastructure like high-contrast grating (HCG) has many unique optical properties which can be used to construct novel VCSELs. Here we study the TE-polarization HCG for 940 nm wavelength range and design high-quality HCG-based vertical cavities with heterostructures aiming at HCG-VCSEL. The TE-polarization HCG-VCSEL at 940 nm is finally designed with a Q-factor of ~3.6×105.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.