Understanding the dynamic behavior of photopolymers in nanoscale environment is essential to improving MEMS/NEMS device fabrication technologies. Here, we unveil the highly nonlinear behaviors of photopolymers exhibited during the process of light-controlled, low-pressure nanoimprinting. Such peculiarities can complicate the relation between the UV-dose and the height of the nanoimprinted feature, degrading the accuracy of the height control. To address the issue, we establish a theoretical process model and used the control of the nanoimprinting height for structural coloring applications. Our findings will broadly benefit nanotechnology and nanoscience.
Recently, there have been notable advances in nanophotonic structural color generation which enabled various applications in display, anti-counterfeiting, sensors and detectors. However, most advances in this domain have been achieved through the use of high-index materials which require expensive and complex fabrication. In this work, we enable low-index polymer nanostructures to generate structural colors using the multipolar decomposition technique which allows a better understanding and design of the scattering process by identifying the dominant multipole modes from the scattered fields. We set a polymeric (n~1.56) cuboid as the structural color generation platform, examined the contributions of various multipoles from the wave scattered by it, and synthesized the desired color spectrum by adjusting only the height of the cuboid. To validate our findings, we fabricated the designed structural color pixels via light-controlled, low-pressure nanoimprinting and measured the color and spectrum from them. Our experimental results agreed well with the simulation results, providing insights for bringing further advances to structural coloring.
Diffraction gratings are ubiquitous in many optical applications such as sensors, filters, and optical security devices. Capillary force lithography, which utilizes the capillary rise of photopolymer into nanoscale cavities, is a simple and rapid method to construct diffraction gratings without necessitating expensive instruments or complex steps. With the help of spatial light modulators, such as the digital micromirror device, the height of the grating can also be spatially modulated, printing spatially height-modulated gratings. When white light normally impinges on the grating, the light propagates into the grating interferes with light that propagates into air. By varying the height of the grating, the optical path lengths of two lights can be varied, leading to different interference effects and structural coloring. Judicious design of the grating’s parameters and patterning process will even allow encoding of multiple images. In this work, by tuning the height of the grating through the light-controlled capillary force lithography, we demonstrate grating-based structural color printing. This technique is promising for producing the custom patterns for anti-counterfeiting, authentication, and cryptography.
In this paper, total internal reflection (TIR) mirror is carefully simulated for silicon nitride polygonal ring resonator sensor structure. Polygonal resonator has recently attracted much attention for applications in bio and chemical sensors because it does not have a bending loss, and it has an advantage of using MMI coupler. In polygonal resonator sensor design, high Q-factor and low TIR mirror loss are extremely significant factors. Therefore, critical angle and Goos-Hanchen shift should be considered in the design of TIR mirror. When cladding material is SiO2, the critical angle of SiNx waveguide is about 44.99 degrees and the Goos-Hanchen shift is about 400 nm at 1.55 μm wavelength. For the rib type waveguide, we designed it to have 3 μm width, 1 μm height, and 0.5 μm etching depth for decreasing TIR mirror loss. As simulation results of FDTD, reflectivitities of polygonal TIR mirrors are 79% for pentagon, 95% for hexagon and 98% for octagon, respectively. According to the simulations, Q-factors for hexagonal and octagonal resonators can be obtained as high as 1.55 x 104 and 1.72 x 104, respectively.
KEYWORDS: Signal to noise ratio, Signal detection, Optical amplifiers, Interference (communication), Telecommunications, Modulation, Sensors, Linear filtering, Capacitors, Cognitive informatics, Optical sensors, Signal processing, Optical design
Lock-in amplifier (LIA) has been widely used in optical signal detection systems because it can measure small signal under high noise level. Generally, The LIA used in optical signal detection system is composed of transimpedance amplifier (TIA), phase sensitive detector (PSD) and low pass filter (LPF). But commercial LIA using LPF is affected by flicker noise. To avoid flicker noise, there is 2ω detection LIA using BPF. To improve the dynamic reserve (DR) of the 2ω LIA, the signal to noise ratio (SNR) of the TIA should be improved. According to the analysis of frequency response of the TIA, the noise gain can be minimized by proper choices of input capacitor (Ci) and feed-back network in the TIA in a specific frequency range. In this work, we have studied how the SNR of the TIA can be improved by a proper choice of frequency range. We have analyzed the way to control this frequency range through the change of passive component in the TIA. The result shows that the variance of the passive component in the TIA can change the specific frequency range where the noise gain is minimized in the uniform gain region of the TIA.
Two-dimensional (2-D) metal nanodot arrays (NDAs) have been attracting significant attention for use in biological and chemical sensing applications. The unique optical properties of the metal NDAs originate from their localized surface plasmon resonance (LSPR). Nanofabrication methods that use nanoporous alumina masks (NAMs) have been widely used to produce metal NDAs. We report a fabrication technique for a 2-D Ag NDA and its utilization as a platform for LSPR-based sensing applications. A well-ordered Ag NDA of ∼70-nm diameter, arranged in a periodic pattern of 105 nm, was fabricated on an indium tin oxide (ITO) glass substrate using an NAM as an evaporation mask. The LSPR of the Ag NDA on the ITO glass was investigated using ultraviolet–visible spectroscopy. The LSPR wavelength shifts caused by the variations in the quantity of methylene blue adsorbed on the Ag NDA were examined. The results of this study suggest that the Ag NDA prepared using NAM can be used as a chemical sensor platform.
In this paper, we propose a bio-sensing method using optical heterodyne detection for ultra-high Q micro-disk laser (MDL) sensor platform. MDL structure with ultra-high Q-factor (> 108) has advantage in detecting a small variation of the lasing wavelength. For example, when a single molecule is attached to sidewall of MDL, the lasing wavelength is changed by sub-pm. Optical spectrum analyzer (OSA) has limits to detect sub-pm variation in the resonant wavelength because of the spectral resolution. In order to overcome this limitation, we used a heterodyne detection method which needs two MDLs with the same characteristics.
The noble metal nanostructure has attracted significant attention because of their potential applications as sensitive sensor platform blocks for biological and chemical sensing. The unique optical property of the metal nanostructure is originated from localized surface plasmon resonance (LSPR). The fabrication of metal nanostructure is a key issue for sensor applications of LSPR. In this paper, fabrication technique of two-dimensional Ag nanodot array on an indium tin oxide (ITO) glass substrate via the nanoporous alumina mask and the utilization as a platform for LSPR chemical sensor was studied. Well-ordered Ag nanodot array with approximately 65 nm diameter in periodic pattern of 105 nm was fabricated using the nanoporous alumina with through-holes as an evaporation mask. The LSPR of Ag nanodot array on ITO glass substrate was investigated by UV-vis spectroscopy. The LSPR wavelength-shifts owing to the concentration variances of Methylene Blue (MB) adsorbed on Ag nanodot arrays were examined for application of chemical sensor.
In this paper, an effective quality-factor is analyzed for asymmetric Mach-Zehnder interferometer (AMZI) with ring resonator sensor. The device is designed with AMZI to interference with the optical input of the ring resonator based on silica semiconductor process. The design of device satisfy a critical resonance at out of phase condition through asymmetric power split ratio. According to operation principle of Mach-Zehnder interferometer, the critical resonance occurs when the power passing through asymmetric arm is in a range of ring resonator power variation. Our simulation shows that the Q-factor of the device is enhanced from 1161.9 to 5342.5 if a RR is coupled to an arm of AMZI.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.