We present an advanced optical design for a high-resolution ultra-compact VR headset for high-end applications based on multichannel freeform optics and 4 OLED WUXGA microdisplays developed under EU project LOMID [1]. Conventional optical systems in VR headsets require large distance between lenses and displays that directly leads to the rather bulky and heavy commercial headsets we have at present. We managed to dramatically decrease the required display size itself and the display to eye distance, making it only 36 mm (to be compared to 60-75 mm in most conventional headsets). This ultra-compact optics allows reducing the headset weight and it occupies about a fourth of volume of a conventional headset with the same FOV. Additionally, our multichannel freeform optics provides an excellent image quality and a large field of view (FOV) leading to highly immersive experience. Unlike conventional microlens arrays, which are also multichannel devices, our design uses freeform optical surfaces to produce, even operating in oblique incidences, the highest optical resolution and Nyquist frequency of the VR pixels where it is needed. The LOMID microdisplays used in our headsets are large-area high-resolution (WUXGA) microdisplays with compact, high bandwidth circuitry, including special measures for high contrast by excellent blacks and low-power consumption. LOMID microdisplay diagonal is 0.98” with 16:10 aspect ratio. With two WUXGA microdisplays per eye, our headset has a total of 4,800x1,920 pixels, i.e. close to 5k. As a result, our multichannel freeform optics provides a VR resolution 24 pixels/deg and a monocular FOV of 92x75 degs (or 100x75 with a binocular superposition of 85%).
We address freeform aplanatic designs both as solutions of a differential system of equations and as limiting cases of SMS designs. We conclude that, in general, freeform aplanatic systems need at least 3 optical-surfaces with illustrative examples.
We present novel advanced optical designs with a dramatically smaller display to eye distance, excellent image quality and a large field of view (FOV). This enables headsets to be much more compact, typically occupying about a fourth of the volume of a conventional headset with the same FOV. The design strategy of these optics is based on a multichannel approach, which reduces the distance from the eye to the display and the display size itself. Unlike conventional microlens arrays, which are also multichannel devices, our designs use freeform optical surfaces to produce excellent imaging quality in the entire field of view, even when operating at very oblique incidences. We present two families of compact solutions that use different types of lenslets: (1) refractive designs, whose lenslets are composed typically of two refractive surfaces each; and (2) light-folding designs that use prism-like three-surface lenslets, in which rays undergo refraction, reflection, total internal reflection and refraction again. The number of lenslets is not fixed, so different configurations may arise, adaptable for flat or curved displays with different aspect ratios. In the refractive designs the distance between the optics and the display decreases with the number of lenslets, allowing for displaying a light-field when the lenslet becomes significantly small than the eye pupil. On the other hand, the correlation between number of lenslets and the optics to display distance is broken in light-folding designs, since their geometry permits achieving a very short display to eye distance with even a small number of lenslets.
In present commercial Virtual Reality (VR) headsets the resolution perceived is still limited, since the VR pixel density (typically 10-15 pixels/deg) is well below what the human eye can resolve (60 pixels/deg). We present here novel advanced optical design approaches that dramatically increase the perceived resolution of the VR keeping the large FoV required in VR applications. This approach can be applied to a vast number of optical architectures, including some advanced configurations, as multichannel designs. All this is done at the optical design stage, and no eye tracker is needed in the headset.
Compacting devices is an increasingly demanding requirement for many applications in both nonimaging and imaging optics. “Compacting” means here decreasing the volume of the space between the entry and the exit aperture without decreasing the optical performance. For nonimaging optical systems, compact optics is mainly important for reducing cost. Its small volume means less material is needed for mass-production and small size and light weight save cost in transportation. For imaging optical systems, in addition to the mentioned advantages, compact optics increases portability of devices as well, which contributes a lot to wearable display technologies such as Head Mounted Displays (HMD). After reviewing the different techniques to design compact systems, we analyze here the multichannel strategies. These type of designs split the incoming bundle of rays in different sub-bundles that are optically processed (independently) and then recombined in a single outgoing bundle. The optics volume decreases rapidly with the number of sub-bundles. These designs usually need to be combined with freeform optics in order to get optimum performance.
Recent advances in the Simultaneous Multiple Surfaces (SMS) design method are reviewed in this paper. In particular,
we review the design of diffractive surfaces using the SMS method and the concept of freeform aplanatism as a limit
case of a 3D SMS design.
Several applications of freeform optics call for deeper analysis of systems with rectangular apertures. We study the behavior of a freeform mirror system by comparing four orthogonal polynomial surface representations through local optimization. We compare polynomials with different orthogonal areas (rectangular-circular) and different metrics (sag-gradient). Polynomials orthogonal inside a rectangle converge faster or to a better local minimum than those orthogonal inside a circle in the example considered. This is the most likely due to the loss of the good properties of orthogonality when the orthogonality area does not coincide with the surface area used.
With the increasing interest in using freeform surfaces in optical systems due to the novel application opportunities and manufacturing techniques, new challenges are constantly emerging. Optical systems have traditionally been using circular apertures, but new types of freeform systems call for different aperture shapes. First non-circular aperture shape that one can be interested in due to tessellation or various folds systems is the rectangular one. This paper covers the comparative analysis of a simple local optimization of one design example using different orthogonalized representations of our freeform surface for the rectangular aperture. A very simple single surface off-axis mirror is chosen as a starting system. The surface is fitted to the desired polynomial representation, and the whole system is then optimized with the only constraint being the effective focal length. The process is repeated for different surface representations, amongst which there are some defined inside a circle, like Forbes freeform polynomials, and others that can be defined inside a rectangle like a new calculated Legendre type polynomials orthogonal in the gradient. It can be observed that with this new calculated polynomial type there is a faster convergence to a deeper minimum compared to “defined inside a circle” polynomials. The average MTF values across 17 field points also show clear benefits in using the polynomials that adapted more accurately to the aperture used in the system.
Axisymmetric aplanatic systems have been used in the past for solar concentrators and condensers (Gordon et. al, 2010).
It is well know that such a system must be stigmatic and satisfy the Abbe sine condition. This problem is well known
(Schwarzschild, 1905) to be solvable with two aspherics when the system has rotational symmetry.
However, some of those axisymmetric solutions have intrinsically shading losses when using mirrors, which can be
prevented if freeform optical surfaces are used (Benitez, 2007).
In this paper, we explore the design of freeform surfaces to obtain full aplanatic systems. Here we prove that a rigorous
solution to the general non-symmetric problem needs at least three free form surfaces, which are solutions of a system of
partial differential equations (PDE). We also present the PDEs for a three surface full aplanat. The examples considered
have one plane of symmetry, where a consistent 2D solution is used as boundary condition for the 3D problem. We have
used the x-y polynomial representations for all the surfaces, and the iterative algorithm formulated for solving the above
said PDE has shown very fast convergence.
Freeform optical surfaces have been in much demand recently due to improved techniques in their manufacturability and design methodology, and the degrees of freedom it gives the designers. Specifically in the case of off-axis mirror systems, freeform surfaces can considerably reduce the number of surfaces and compensate for some of the higher order aberrations as well, which improves the overall system performance. In this paper, we explore the design of freeform surfaces to obtain full aplanatic mirror systems, i.e., free of spherical aberration and circular coma of all orders. It is well know that such a system must be stigmatic and satisfy the Abbe sine condition. This problem is well known (Schwarzschild, 1905) to be solvable with two aspheric when the system has rotational symmetry. Here we prove that a rigorous solution to the general non-symmetric problem needs at least three free form surfaces, which are solutions of a system of partial differential equations. The examples considered have one plane of symmetry, where a consistent 2D solution is used as boundary condition for the 3D problem. We have used the x-y polynomial representations for all the surfaces used, and the iterative algorithm formulated for solving the above mentioned partial differential equations has shown very fast convergence.
Axisymmetric aplanatic concentrators have been used in the past for solar concentrators and condensers (Gordon et. al, 2010). It is well know that such a system must be stigmatic and satisfy the Abbe sine condition. This problem is well known (Schwarzschild, 1905) to be solvable with two aspherics when the system has rotational symmetry. However, some of those axisymmetric solutions have intrinsically shading losses when using mirrors, which can be prevented if freeform optical surfaces are used (Benitez, 2007). In this paper, we explore the design of freeform surfaces to obtain full aplanatic systems. Here we prove that a rigorous solution to the general non-symmetric problem needs at least three free form surfaces, which are solutions of a system of partial differential equations (PDE). We also present the PDEs for a three surface full aplanat. The examples considered have one plane of symmetry, where a consistent 2D solution is used as boundary condition for the 3D problem. We have used the x-y polynomial representations for all the surfaces, and the iterative algorithm formulated for solving the above said PDE has shown very fast convergence.
In this work, we demonstrate how it is possible to sharply image multiple object points. The Simultaneous Multiple Surface (SMS) design method has usually been presented as a method to couple N wave-front pairs with N surfaces, but recent findings show that when using N surfaces, we can obtain M image points when N<M under certain conditions. We present the evolution of SMS method, from its basics, to imaging two object points through one surface, the transition from two to three objet points obtained by increasing the parallelism, and getting to the designs of six surfaces imaging up to eight object points. These designs are limited with the condition that the surfaces cannot be placed at the aperture stop. In the process of maximizing the object points to sharp image, we try to exhaust the degrees of freedom of aspherics and free-forms. We conjecture that maximal SMS designs are very close to a good solution, hence using them as a starting point for the optimization will lead us faster to a final optical system. We suggest here different optimization strategies which combined with the SMS method are proven to give the best solution. Through the example of imaging with the high aspect ratio, we compare the results obtained optimizing the rotational lens and using a combination of SMS method and optimization, showing that the second approach is giving significantly smaller value of overall RMS spot diameter.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.