|
1.IntroductionAdvances of organic light-emitting diodes (OLEDs) and their display and lighting applications continuously impose requirements on high-efficiency materials and devices.1–8 Since the pioneering introduction of thermally activated delayed fluorescence (TADF) emitters in OLEDs by Uoyama et al.,2 TADF materials have attracted intensive research in the past few years. This is mainly due to the capability of TADF materials in harvesting triplet excitons by the thermally activated upconversion and in giving possible 100% internal quantum efficiency in electroluminescence (EL), through purely organic molecular frameworks and without the need to incorporate transition metals like in phosphorescent emitters.1–8 In TADF molecules, through reducing the spatial overlap between the highest occupied molecular orbital and the lowest unoccupied molecular orbital, the energy gap () between the lowest excited singlet () and triplet () states can be effectively reduced to facilitate efficient upconversion of excitons to .2,5–8 On the other hand, the optical outcoupling is also a critical issue for enhancing the overall external quantum efficiency (EQE) of OLEDs for practical use.9,10 In addition to many other optical approaches and structures,11–15 reports in recent years have revealed the importance of the emitting dipole orientations of OLED emitters relative to the device plane.4,15–18 Horizontal emitting dipoles generate emission patterns (angular distributions of radiation) more suitable for direct outcoupling of internal light to the air, while radiation of vertical emitting dipoles couples strongly to waveguide (WG) modes and hugely to surface plasma (SP) modes for its transverse magnetic (TM) field-only nature. Since WG and SP modes are generally trapped and lost inside the OLED devices, preferentially horizontal dipole emitters having larger ratios of horizontal emitting dipoles that generally benefit higher-efficiency OLEDs (even without adopting any extra optical outcoupling techniques) have been intensively studied in recent years. In our recent works,19,20 we reported a series of efficient donor–acceptor (D-A) TADF emitters: SpiroAC-TRZ, DPAC-TRZ, DMAC-TRZ (Fig. 1) based on hybrids of the 2,4,6-triphenyl-1,3,5-triazine (TRZ) acceptor unit and the dimethyl, diphenyl, spirobiphenyl acridine donor units (DMAC, DPAC, SpiroAC). Some selected photophysical and EL properties of these TADF emitters doped in a bipolar and wide-triplet-energy host mCPCN [9-(3-(-carbazol-9-yl)phenyl)--carbazole-3-carbonitrile] (12 wt.% doping concentration) are listed in Table 1. These acridine–triazine hyrbrids are blue–green to sky blue emitters, all showing relatively small of 62 to 133 meV, distinct TADF characteristics with delayed fluorescence lifetimes of 1.9 to , high photoluminescence quantum yields (PLQYs) of 82% to 100%, preferentially horizontal emitting dipoles (with horizontal dipole ratios of 72% to 83%). Most importantly, these TADF emitters can be used to fabricate high-efficiency TADF OLEDs with high EQEs of 26% to 37%. Among these acridine–triazine hybrids, the sky–blue SpiroAC-TRZ gives particularly highest PLQY of , highest horizontal dipole ratio of 83%, and highest device EQE of . Although SpiroAC-TRZ possesses nearly ideal PLQY of and relatively high horizontal emitting dipole ratio of 83%, its very high device EQE of up to was still rather surprising. Although the horizontal emitting dipole ratio of 83% is high but not yet extremely high, the calculated optical outcoupling efficiency of up to in a conventional planar OLED structure was also quite surprising.20 Thus, detailed mechanisms of the very high optical outcoupling efficiencies and EL EQEs in our devices are certainly of interest. Here, we adopt the dipole-based electromagnetic model to quantitatively analyze and discuss the optical outcoupling efficiencies and EQEs in these TADF OLEDs. Table 1Selected photophysical and EL properties for acidine–triazine hybrid-based TADF emitters.
2.Simulation MethodThe simulation tool used for optical simulation of layer structures is developed by ourselves and is based on the equivalence between molecular emission through electronic dipole transitions and radiation from a classical electrical dipole antenna.9,10,20 With the Fourier transformation of a dipole field into the domain and the transfer matrix method to determine the properties of propagation, electromagnetic fields generated by a radiation dipole embedded in a layered structure are calculated, from which the distribution of the power density (dissipated to different modes) in each plane parallel to the device can be derived. The far-field intensity into substrate and into air is calculated by far-field approximation. Overall emission characteristics of an OLED are calculated by assuming that the emitting layer (EML) contains an ensemble of mutually incoherent dipole radiators with distributions in orientations, locations, and frequencies. The outcoupling efficiencies of internally generated radiation into air were calculated by locating emitting dipoles in the EML and by considering the orientational distribution () and the full spectral distribution of radiating dipoles. When calculating the pure optical outcoupling efficiency, the emitters are assumed to have 100% emission quantum efficiency. 3.Quantitative Analyses of High Electroluminescence EfficienciesEfficient OLEDs based on these acridine–triazine hybrids adopted the general device structure of: glass substrate/indium tin oxide (ITO) (70 nm/ (1 nm)/di-[4-(-ditolyl-amino)-phenyl]-cyclohexane (TAPC) ( nm)/mCP (10 nm)/mCPCN doped with TADF dopants (12 wt.%, 20 nm)/3TPYMB ( nm)/LiF (0.5 nm)/Al (150 nm).20 ITO and Al were anode and cathode, repsectiely. TAPC and -dicarbazolyl-3,5-benzene (mCP) were hole-transport layers (HTL). The bipolar mCPCN host and TADF dopants constituted the EML. Tris-[3-(3-pyridyl)mesityl]borane (3TPYMB) was the ETL. and LiF were employed as hole and electron-injection layers (HIL, EIL). In calculating optical outcoupling efficiencies and overall emission characteristics, optical properties of various layers need to be input. In addition to the high PLQYs and preferentially horizontal emitting dipoles, we also noticed that the TAPC HTL and the 3TPYMB ETL have relatively low refractive indices (), compared to many other HTL and ETL materials commonly used in OLEDs. Figure 2(a) shows the refractive index of TAPC, in comparison with those of several common HTL materials like NPB and TCTA, while Fig. 2(b) shows the refractive index of 3TPYMB, in comparison with those of several common ETL materials. It is seen that around the wavelengths of interest here (sky-blue to blue-green), various HTL and ETL materials could exhibit widely varied refractive indices, ranging from to . Importantly, perhaps TAPC has the lowest () among various HTL materials and 3TPYMB has the lowest () among various ETL materials known in the literature. Lower refractive indices of active organic layers in OLEDs are in general beneficial to OLED efficiencies, since the high refractive indices of OLED active layers are one of the major factors limiting optical outcoupling efficiencies. Several groups have shown that adoption of lower-refractive-index HIL, HTL, or ETL can enhance the light extraction efficiency of OLEDs.21–26 To investigate the influences of HTL refractive index () and ETL refractive index (), we calculate the optical coupling/outcoupling efficiencies into air () and into the substrate () for OLEDs adopting the DMAC-TRZ/DPAC-TRZ/SpiroAC-TRZ doped mCPCN EML and HTL/ETL of varied refractive indices, using the general device structure of: glass/ITO (70 nm)/HTL ( nm, )/EML (mCPCN:12 wt.% TADF emitter, 20 nm)/ETL ( nm, )/LiF/Al. The EML is assumed to have horizontal emitting dipole ratio and intrinsic emission spectrum of DMAC-TRZ (72%)/DPAC-TRZ (78%)/SpiroAC-TRZ (83%). Figures 3(a)–3(c) show calculated optimized for DMAC-TRZ/DPAC-TRZ/SpiroAC-TRZ devices as a function of and , while Figs. 3(d)–3(f) show calculated optimized for DMAC-TRZ/DPAC-TRZ/SpiroAC-TRZ devices as a function of and . These optimized efficiencies are extracted from the first maximum value in varying and (HTL/ETL thicknesses) under certain and . Both and monotonically increase as and decrease and as the horizontal emitting dipole ratio increases. It is seen that as both and decrease by 0.1, can increase by 4% to 6%. If both and can be lowered to 1.3, (, ) can reach (, ) for SpiroAC-TRZ device (with higher in EML) and (, ) for DMAC-TRZ device (with lower in EML). In the actual devices using TAPC HTL ( ) and 3TPYMB ETL ( ), calculated (, ) for DMAC-TRZ/DPAC-TRZ/SpiroAC-TRZ devices are (, ), ( to 36%, ), and (, ), respectively. These results well support the very high EQE of achieved for the planar SpiroAC-TRZ device and high EQE of achieved when attached with extraction lens to the substrate.20 To further investigate the mechanism of high optical outcoupling efficiency, the power densities (or the mode distribution) as a function of for the SpiroAC-TRZ based device (at the PL peak wavelength) under different conditions are simulated and are shown in Fig. 4, where is the transverse component of the wavenumber (i.e., along the device plane) and is the wavenumber in vacuum. Figure 4(a) shows the calculated power densities for fixed and varied from 2.0 to 1.3, in which various modes such as the radiation modes, substrate modes, TM waveguided modes (), transverse electric (TE) waveguided modes (), and surface plasmon modes (SP, which is of TM nature) can be seen and assigned. As decreases from 2.0 to 1.3, the SP peak shifts substantially from to 1.7. Since such a shift would lead to overlap of SP modes with modes (roughly fixed around ) in some cases, TE and TM components of the power densities for the selected range of to 2.1 for various , are depicted separately in Figs. 4(b) and 4(c), respectively, so that and SP parts (and also ) can be more clearly distinguished. As seen in Fig. 4(c), in addition to the peak shift, the SP band also narrows significantly (thus integrated areas decrease) when lowering , which is beneficial for reducing the SP loss and for enhancing the optical outcoupling efficiency. The band (around to 1.6) also shows a similar shift toward smaller and narrowing (although less significantly). By contrast, the band position and width [Fig. 4(b)] are more or less fixed around . The fraction ratios of various modes are shown in Fig. 4(d). While ratios of both SP and modes decrease with lower , the ratio of modes roughly remains constant. Thus, both increased radiation mode ratios (i.e., enhanced optical outcoupling) and substrate mode ratios with lower observed in Figs. 4(a) and 4(d) can mainly be attributed to reduction of SP and modes. Figures 5(a) and 5(b) show the distributions of field intensities (electric field E for the mode and magnetic field H for and SP modes) for the modes corresponding to , , and SP peaks for the OLED having typical high and for the OLED having high . For typical OLEDs having high , the mode mainly distributes in ITO and HTL; the mode distributes around both the metal/ETL interface and the ITO/substrate interface; the SP mode peaks at the metal/ETL interface and decays toward the substrate. With reduced , the field distribution of the SP mode shifts more toward the ITO from the metal interface because the relatively high of HTL and ITO tends to attract the field/photon energy, forming a more WG-like SP mode (or WG-SP hybrid mode). Comparison of Figs. 5(a) and 5(b) also reveals more similar field distributions for modes at , which is understandable since modes are roughly confined in ITO and high- HTL and the variation of would less influence their field distributions and peak positions. On another note, for the case of low and high , the electromagnetic fields in the device are more confined in ITO and HTL, which might be useful for obtaining effective light extraction by some internal light extraction structures near/within ITO. Similarly, Figs. 4(e)–4(h) show the overall power densities, TM and TE components of the power densities for the selected range of to 2.0, and the fraction ratios of various modes, respectively, for fixed and varied from 2.0 to 1.3. The SP peaks also shift toward smaller as decreases [Fig. 4(g)], but the shift is smaller compared to those in Fig. 4(c). The shift of SP peaks toward smaller upon reducing and in general is due to lower effective refractive indices of the dielectric layers in front of the metal surface. The larger shift with reduced than with reduced is because the ETL is more adjacent to the metal layer. Also, the integrated areas of SP modes [also the fraction ratio of SP modes in Fig. 4(h)] do not change evidently when varies, thus not contributing to enhancement of optical outcoupling efficiency. Meanwhile, both and modes shift toward smaller as decreases. In addition to the peak shift, their bandwidths and intensities also drop (thus reduced integrated areas) when lowers, resulting in reduction of both trapped WG modes, as clearly indicated in Fig. 4(h). This reduction of trapped WG modes is the main contributor to the enhancement of by [Fig. 3(f)] as decreases from 2.0 to 1.3 (while fixed at 1.8). However, it cannot fully account for the significantly larger increase of by to 16% [Fig. 3(c)] as decreases from 2.0 to 1.3 (while fixed at 1.8). In Fig. 4(e), one notices that, as decreases, not only the overall radiation coupling into the substrate (i.e., radiation + substrate modes) increases but also its distribution shifts toward to smaller (i.e., larger ratio of radiation is relocated into smaller angles for direct outcoupling), resulting in larger enhancement over the overall enhancement [as also clearly seen in Fig. 4(h)]. This more concentrated angular distribution (in the substrate) is associated with the enhanced microcavity effect resulting from the increased index difference and optical reflection between the high- ITO and the low- HTL (thus like a pair of dielectric mirror). Indeed, the calculated reflectance spectra for the complete OLED with different ( fixed at 1.8), as shown in Fig. 6, clearly exhibit stronger resonance for lower . Figure 5(c) shows the distributions of field intensities for the modes corresponding to , , and SP peaks for the OLED having low . Comparison of Figs. 5(a) and 5(c) reveals that the field distributions of and SP modes remain similar but becomes more concentrated in ITO when decreases. Since in the high-efficiency SpiroAC-TRZ devices, both the HTL (TAPC) and ETL (3TPYMB) have similarly low refractive indexes (), we have also analyzed mode properties for the case of . Figures 4(i)–4(l) show the overall power densities, TM and TE components of the power densities for the selected range of to 2.0, and the fraction ratios of various modes, respectively, for varied from 2.0 to 1.4. In reducing , mode properties shown in Figs. 4(j)–4(k) appear to combine features seen for cases of low- HTL and low- ETL. All the SP, , and bands shift toward smaller and narrow significantly. As a result, fraction ratios of SP, , and modes all drop with , together contributing to even more significant enhancement of substrate + radiation modes [see Figs. 3(f), 4(i), and 4(l)]. Interestingly, the fraction ratio of substrate modes remains more or less constant in reducing [Figs. 4(i) and 4(l)], and reduction of SP, , and modes indeed mainly leads to enhancement of the radiation modes that can be directly outcoupled (i.e., enhancement of ). As decreases, in Fig. 4(i), one again observes more concentrated angular distribution of radiation coupled into the substrate (within smaller angles, i.e., at ), more readily for direct outcoupling. This more concentrated angular distribution (in the substrate) is again associated with the enhanced microcavity effect resulting from the increased index difference and optical reflection between the high- ITO and the low- HTL. Thus, intriguingly, upon reducing both and , the enhancement of optical outcoupling is not only from reduced modes (due to low- HTL/ETL) but also from enhanced microcavity effect and more angularly concentrated distribution in the substrate. These together give even more significant enhancement of optical outcoupling compared to the simply low-n ETL or low-n HTL case. 4.ConclusionIn summary, we had used the dipole-based electromagnetic model to quantitatively analyze why the surprisingly high EQE of can be achieved in previously reported OLEDs using TADF emitters based on the acridine–triazine hybrids. It is found that in addition to the high PLQYs and preferentially horizontal emitting dipoles, the use of low-index HTLs and ETLs also substantially help enhance the optical outcoupling efficiencies and EQEs of the devices. Although lowering refractive indices of either HTLs or lowering those of ETLs are both similarly effective to enhance OLED optical outcoupling efficiency, detailed enhancement mechanisms are different. The enhancement of optical outcoupling with low-index ETLs is mainly due to reduced SP modes and TM waveguided modes that are more affected by the refractive index of ETLs. On the other hand, the enhancement with low-index HTLs is due to reduced WG modes (both TE and TM modes that are affected by the refractive index of HTLs) and also enhanced microcavity effect that causes more angularly concentrated radiation more readily for direct outcoupling. Most importantly, when reducing refractive indexes of both HTLs and ETLs, all these mechanisms (reduced SP/TE/TM modes, microcavity effect) combine together to give even more significant enhancement in optical outcoupling. In general, upon reducing refractive indexes of both by 0.1, optical outcoupling efficiencies can increase by 4% to 6%. Results of this work should be useful for better understanding the material design and device architecture for highly efficient OLEDs and also clearly indicate that both electrical and optical properties of carrier-transport layers should be carefully considered for future development of high-efficiency OLEDs. AcknowledgmentsThe authors gratefully acknowledge the financial support from the Ministry of Science and Technology of Taiwan (MOST) under Grants 104-2221-E-002-152-MY3. ReferencesM. A. Baldo et al.,
“Highly efficient phosphorescent emission from organic electroluminescent devices,”
Nature, 395 151
–154
(1998). https://doi.org/10.1038/25954 Google Scholar
H. Uoyama et al.,
“Highly efficient organic light-emitting diodes from delayed fluorescence,”
Nature, 492 234
–238
(2012). https://doi.org/10.1038/nature11687 Google Scholar
H. Sasabe et al.,
“Recent progress in phosphorescent organic light-emitting devices,”
Eur. J. Org. Chem., 2013 7653
–7663
(2013). https://doi.org/10.1002/ejoc.v2013.34 Google Scholar
C.-Y. Kuei et al.,
“Bis-tridentate Ir(III) complexes with nearly unitary RGB phosphorescence and organic light-emitting diodes with external quantum efficiency exceeding 31%,”
Adv. Mater., 28 2795
–2800
(2016). https://doi.org/10.1002/adma.201505790 ADVMEW 0935-9648 Google Scholar
Y. J. Cho et al.,
“20% external quantum efficiency in solution-processed blue thermally activated delayed fluorescent devices,”
Adv. Funct. Mater., 25
(43), 6786
–6792
(2015). https://doi.org/10.1002/adfm.201502995 AFMDC6 1616-301X Google Scholar
W.-C. Chen et al.,
“Blue-emitting organic electrofluorescence materials: progress and prospective,”
J. Mater. Chem. C, 3 10957
–10963
(2015). https://doi.org/10.1039/C5TC02420J Google Scholar
K. Shizu et al.,
“Highly efficient electroluminescence from purely organic donor-acceptor systems,”
Pure Appl. Chem., 87 627
–638
(2015). https://doi.org/10.1515/pac-2015-0301 PACHAS 0033-4545 Google Scholar
Y. Tao et al.,
“Thermally activated delayed fluorescence materials towards the breakthrough of organoelectronics,”
Adv. Mater., 26 7931
–7958
(2014). https://doi.org/10.1002/adma.v26.47 ADVMEW 0935-9648 Google Scholar
C.-L. Lin et al.,
“Enhancing light outcoupling of organic light-emitting devices by locating emitters around the second antinode of the reflective metal electrode,”
Appl. Phys. Lett., 88 081114
(2006). https://doi.org/10.1063/1.2178485 APPLAB 0003-6951 Google Scholar
K. Neyts,
“Microcavity effects and the outcoupling of light in displays and lighting applications based on thin emitting films,”
Appl. Surf. Sci., 244 517
–523
(2005). https://doi.org/10.1016/j.apsusc.2004.09.156 ASUSEE 0169-4332 Google Scholar
Y. Sun et al.,
“Organic light emitting devices with enhanced outcoupling via microlenses fabricated by imprint lithography,”
J. Appl. Phys., 100 073106
(2006). https://doi.org/10.1063/1.2356904 JAPIAU 0021-8979 Google Scholar
H.-W. Chang et al.,
“Nano-particle based scattering layers for optical efficiency enhancement of organic light-emitting diodes and organic solar cells,”
J. Appl. Phys., 113 204502
(2003). https://doi.org/10.1063/1.4807000 JAPIAU 0021-8979 Google Scholar
Y. R. Do et al.,
“Enhanced light extraction from organic light-emitting diodes with 2D photonic crystals,”
Adv. Mater., 15 1214
–1218
(2003). https://doi.org/10.1002/adma.200304857 ADVMEW 0935-9648 Google Scholar
J. Feng, T. Okamoto and S. Kawata,
“Highly directional emission via coupled surface-plasmon tunneling from electroluminescence in organic light-emitting devices,”
Appl. Phys. Lett., 87 241109
(2005). https://doi.org/10.1063/1.2142085 APPLAB 0003-6951 Google Scholar
C.-Y. Chen et al.,
“Enhancing optical out-coupling of organic light-emitting devices with nanostructured composite electrodes consisting of indium tin oxide nanomesh and conducting polymer,”
Adv. Mater., 27 4883
–4888
(2015). https://doi.org/10.1002/adma.v27.33 ADVMEW 0935-9648 Google Scholar
J. W. Sun et al.,
“A fluorescent organic light-emitting diode with 30% external quantum efficiency,”
Adv. Mater., 26 5684
–5688
(2014). https://doi.org/10.1002/adma.201401407 ADVMEW 0935-9648 Google Scholar
H. Kaji et al.,
“Purely organic electroluminescent material realizing 100% conversion from electricity to light,”
Nat. Commun., 6 8476
(2015). https://doi.org/10.1038/ncomms9476 NCAOBW 2041-1723 Google Scholar
C. Mayr et al.,
“Efficiency enhancement of organic light-emitting diodes incorporating a highly oriented thermally activated delayed fluorescence emitter,”
Adv. Funct. Mater., 24 5232
–5239
(2014). https://doi.org/10.1002/adfm.v24.33 AFMDC6 1616-301X Google Scholar
W.-L. Tsai et al.,
“A versatile thermally activated delayed fluorescence emitter for both highly efficient doped and non-doped organic light emitting devices,”
Chem. Commun., 51 13662
–13665
(2015). https://doi.org/10.1039/C5CC05022G Google Scholar
T.-A. Lin et al.,
“Sky-blue organic light emitting diode with 37% external quantum efficiency using thermally activated delayed fluorescence from spiroacridine-triazine hybrid,”
Adv. Mater., 28 6976
–6983
(2016). https://doi.org/10.1002/adma.201601675 ADVMEW 0935-9648 Google Scholar
Y.-H. Huang et al.,
“Unlocking the full potential of conducting polymers for high-efficiency organic light-emitting devices,”
Adv. Mater., 27 929
–934
(2015). https://doi.org/10.1002/adma.v27.5 ADVMEW 0935-9648 Google Scholar
M. Jiao et al.,
“Simple planar indium-tin-oxide-free organic light-emitting devices with nearly 39% external quantum efficiency,”
Adv. Opt. Mater., 4 365
–370
(2016). https://doi.org/10.1002/adom.201500576 2195-1071 Google Scholar
C.-Y. Lu et al.,
“Achieving above 60% external quantum efficiency in organic light-emitting devices using ITO-free low-index transparent electrode and emitters with preferential horizontal emitting dipoles,”
Adv. Funct. Mater., 26 3250
–3258
(2016). https://doi.org/10.1002/adfm.201505312 AFMDC6 1616-301X Google Scholar
H. Shin et al.,
“Blue phosphorescent organic light-emitting diodes using an exciplex forming co-host with the external quantum efficiency of theoretical limit,”
Adv. Mater., 26 4730
–4734
(2014). https://doi.org/10.1002/adma.v26.27 ADVMEW 0935-9648 Google Scholar
H. Shin et al.,
“Sky-blue phosphorescent OLEDs with 34.1% external quantum efficiency using a low refractive index electron transporting layer,”
Adv. Mater., 28 4920
–4925
(2016). https://doi.org/10.1002/adma.v28.24 ADVMEW 0935-9648 Google Scholar
C. Fuchs et al.,
“Enhanced light emission from top-emitting organic light-emitting diodes by optimizing surface plasmon polariton losses,”
Phys. Rev. B, 92 245306
(2015). https://doi.org/10.1103/PhysRevB.92.245306 Google Scholar
BiographyWei-Kai Lee is currently a PhD student at Graduate Institute of Electronics Engineering, National Taiwan University (NTU), Taiwan. He received his MS degree in the Graduate Institute of Electronics Engineering, NTU, in 2015 and his BS degree in the Department of Electrical Engineering, NTU, in 2013. His research fields include OLED devices, OLED optics and modeling, optical, and photophysical properties of OLED materials, and related device/display technologies. |