Open Access
12 May 2020 Subwavelength self-imaging in cascaded waveguide arrays
Wan-ge Song, Hanmeng Li, Shenglun Gao, Chen Chen, Shining Zhu, Tao Li
Author Affiliations +
Abstract

Self-imaging is an important function for signal transport, distribution, and processing in integrated optics, which is usually implemented by multimode interference or diffractive imaging process. However, these processes suffer from the resolution limit due to classical wave propagation dynamics. We propose and demonstrate subwavelength optical imaging in one-dimensional silicon waveguide arrays, which is implemented by cascading straight and curved waveguides in sequence. The coupling coefficient between the curved waveguides is tuned to be negative to reach a negative dispersion, which is an analog to a hyperbolic metamaterial with a negative refractive index. Therefore, it endows the waveguide array with a superlens function as it is connected with a traditional straight waveguide array with positive dispersion. With a judiciously engineered cascading silicon waveguide array, we successfully show the subwavelength self-imaging process of each input port of the waveguide array as the single point source. Our approach provides a strategy for dealing with optical signals at the subwavelength scale and indicates functional designs in high-density waveguide integrations.

1.

Introduction

Precisely manipulating the optical field at the subwavelength scale is vital both in current imaging technology and on-chip photonic integrations. In pursuing super-resolution imaging, a striking design of a superlens based on negative index metamaterials (NIM) has been proposed;16 it is a revolutionary change in principle and quite different from the other strategies, such as fluorescence microscopy710 and structured light microscopy.1113 To circumvent the extreme difficulties in achieving the initially proposed NIM with negative permeability and permittivity, hyperbolic metamaterials were proposed in which multilayered metal–dielectric structures and metallic nanowires arrays were designed for two kinds of hyperbolic dispersions.1419 Unfortunately, these designs for superlens imaging remain unsatisfactory due to insurmountable manufacturing challenges and huge losses from impedance mismatch at the interface between these NIMs and a positive background. Therefore, demonstrations of a superlens in the optical regime were rarely reported.6,1719

On the other hand, photonic waveguide arrays are widely used for the flexible control of light.2033 Negative refraction, deep-subwavelength focusing, and reconstruction of initial state have been demonstrated.2129 In fact, a waveguide array bears similarities with metamaterials as its lattice is much smaller than the wavelength in the effective medium regime. For example, the multilayer nanofilms or the arrayed-nanorod metamaterials [Fig. 1(b)] can be treated as planar [one-dimensional (1-D)] or cylindrical [two-dimensional (2-D)] waveguides arrays. It is particularly noteworthy that the coupling between the nanofilms or nanorods plays an important role in constructing the special dispersion since they are closely packed together. Therefore, it is quite possible to use the waveguides with controlled coupling to mimic the hyperbolic metamaterials with an effective negative index. By doing this, structures can be greatly simplified while many of their unusual properties and functionalities can be preserved, for example, imaging beyond the diffraction limit.

Fig. 1

Superlens design with cascaded waveguides. (a) Negative refractive index material for superlens imaging. (b) Examples of hyperbolic metamaterials: multilayered metal–dielectric structure and nanorod arrays (top panel) and isofrequency surfaces of extraordinary waves in hyperbolic metamaterials (bottom panel). (c) Compensated positive and negative coupling in waveguide array for superlensing. (d) Dispersion relation for positive and negative coupling. The red arrows indicate the energy flow.

AP_2_3_036001_f001.png

In this paper, we propose a cascaded straight and curved 1-D silicon waveguide array to access subwavelength self-imaging, where the curved waveguides array works as a negative index material with a well-engineered negative dispersion,32 while the straight part acts as normal positive index material. It is noted that the directly cascaded waveguides have almost the same propagation constant, which gives rise to the perfect impedance matching condition and greatly prohibits the scattering loss on the interface. In the experiments, different input ports of the waveguide array are illuminated as point sources and well reconstructed with the dimension smaller than λ/2 through the light evolutions inside the cascaded waveguides. By contrast, in the uniform straight and curved waveguide cases, the optical field propagates in the well-known discrete diffractions with dispersed field distributions at output ports. Because waveguides are packed in the subwavelength dimension, the imaging process breaks the diffraction limit with respect to the free-space wavelength, which offers a powerful means of manipulating the optical field in the subwavelength scale by coupled waveguides. In addition, the capability of restoring the input signal provides a practical solution for high-density silicon photonic integration with low crosstalk.34,35

2.

Design of One-Dimensional Superlens by Cascaded Waveguides

Figure 1(c) shows the scheme of a superlens constructed by cascaded waveguide arrays. We propose two sets of coupled optical waveguide arrays in series with the same period d and different signs of the coupling coefficient. One is positive (c>0), and the other is negative (c<0). Using coupled-mode theory (CMT), the dispersion relation is kz=2ccos(kxd), where kx(kz) is the spatial momentum in the x(z) direction [see Fig. 1(d)]. The red arrows indicate the energy flows. It is clear that the incident beam will be negatively refracted at the interface of the positive and negative coupled waveguides regions. To realize the negative coupling, sinusoidally curved waveguides are designed with the transverse oscillation as a function of propagation distance (in z direction) as x0(z)=Acos(2πz/P), where P is the modulation period and A is the oscillation amplitude [see Fig. 2(e)]. The optical field propagation within the curved waveguide array can be described by the CMT in the tight-binding approximation

Eq. (1)

iψnz+cψn1+cψn+1+x¨0(z)xn2πn0λψn=0,
where n enumerates the waveguides, ψn denotes the optical field in the n’th waveguide, xn is the waveguide position, n0 is the refractive index of the substrate, and c denotes the coupling coefficients between the waveguides in a straight array (i.e., A=0) for a certain distance d (d=|xnxn1|). The effective coupling coefficient of the sinusoidally curved waveguides is given as33

Eq. (2)

ceff=cJ0(2πAω/P),
where J0 is the lowest-order Bessel function of the first kind. ω=2πn0d/λ is the dimensionless optical frequency. The effective coupling coefficient can be tuned by changing the modulation parameters (A and P) or the optical frequency (ω). Here, we consider the change of modulation amplitude A without losing the impedance matching condition of the interface. The red curve in Fig. 2(b) displays the theoretically calculated ceff as a function of A (here, d=0.6  μm, P=10  μm, λ=1.55  μm, and n0=1.75); it is evident that the positive and negative couplings can be achieved by selecting a different A.

Fig. 2

Simulation results in 1-D silicon waveguide arrays. (a) Coupling coefficient as a function of the period of waveguides, where the red dot indicates the period we selected in our modeling. (b) Theoretical and simulated effective coupling coefficient ceff as a function of modulation amplitude A, where the red and black dots indicate the parameters of waveguides we selected in our modeling. Morphology of Si waveguide array with 13 (c) straight waveguides, (e) sinusoidally curved waveguides, and (g) cascaded waveguides, and their corresponding results of the simulated field evolution in (d), (f), and (h), respectively. Simulated signal results of “0”/“1” coded signal transmission through (i) straight, (j) curved, and (k) cascaded waveguide arrays. The output in cascaded waveguides perfectly reproduces the input signal, while the straight and curved waveguides give rise to a chaotic output signal.

AP_2_3_036001_f002.png

According to the above considerations, we constructed the silicon waveguide arrays and employed a commercial finite-element analysis solver (COMSOL Multiphysics 5.3) for full-wave simulations. Each waveguide in the array is defined by silicon with a refractive index nSi=3.48 at λ=1550  nm, width w=400  nm, and height h=220  nm, lying on a sapphire substrate (nAl2O3=1.75), and in the air background. According to these parameters, only the fundamental mode is accommodated in the silicon waveguide at λ=1550  nm with a propagation constant of β0=2.16k0 (k0=2π/λ is the wave vector in free space). In our simulation, we use the open boundary condition (i.e., scattering boundary condition in COMSOL Multiphysics 5.3) and fundamental transverse electric (TE0) mode as the excitation. Figure 2(a) shows the simulated coupling coefficient as a function of the straight waveguides distance d (center-to-center distance); the coupling coefficient is a positive value that decreases as the distance increases. Here, we fixed the period of waveguides to d=0.6  μm (waveguide gap 0.2  μm), corresponding to c=0.081  μm1 for straight waveguides (i.e., A=0). For the curved waveguides, when the modulation amplitude A increases with a fixed modulation period P=10  μm, the effective coupling ceff decreases and tends to be negative [see the blue curve in Fig. 2(b)]. Here, the simulated maximum A is set as 1  μm to avoid a big scattering loss for a larger A. It should be noted that the simulated effective coupling coefficient (blue curve) deviates from the theory (red curve) in the large A region. This is because Eq. (2) is an approximate expression in the small curvature condition. Actually, a slowly varying bending profile, the nearest-neighbor tight-binding approximation, and a weak refractive index change of waveguides from the substrate index are required to derive Eq. (2). However, our simulation setup of high-density silicon waveguides certainly breaks these approximations and leads to the differences. Despite the deviation, the crucial effect of the negative coupling by curved waveguides is still retained in our case. According to the simulation results, 13 waveguides are designed in the arrays both for the straight (Ap=0) and curved (An=1  μm) ones with corresponding coupling coefficients of cn=cp=0.081  μm1. Figure 2(g) shows the cascaded waveguide arrays by connecting each waveguide straightforwardly. To provide direct comparisons, simple straight and curved waveguide arrays were also investigated, as shown in Figs. 2(c) and 2(e).

Figures 2(d), 2(f), and 2(h) show the simulated results of light propagations within 40-μm-long silicon waveguides of straight, curved, and cascaded samples, respectively, with the excitation of a single waveguide at the center as the input signal. The well-known discrete diffraction behaviors20 are observed in both the positively and negatively coupled waveguides, in which light spreads toward two sides as it propagates [see Figs. 2(d) and 2(f)]. It is also confirmed that, in the curved sample, the negative coupling only affects the coupling phase of the evolution fields and intensity distributions evolution remains almost the same as for the positive dispersion case. For the cascaded sample, the light first undergoes the discrete diffraction in the straight part and converges in an inverse process of discrete diffraction in the curved part. As a result, the power of the optical field remains localized around the center waveguide at the outputs, indicating a self-imaging function. This revival process is attributed to the π phase changes of the field coupling with opposite coupling strength. It should be noted that the period of waveguides (d=0.6  μm) is beyond the diffraction limit (0.775  μm) with respect to the free space wavelength. The cascaded waveguide array indeed works as a superlens for subdiffraction imaging. Furthermore, we find that the self-imaging effect can be used to transmit an arbitrarily complex signal by such a waveguide system with subwavelength resolution. To verify this, further simulations were performed on straight, curved, and cascaded waveguides samples with multiple ports input as an arbitrary signal [i.e., (1010011010010), here “1”/“0” represents with/without light input], and the results are shown in Figs. 2(i)2(k), respectively. As expected, the output signal in cascaded waveguides is exactly the same as the input revealing a subwavelength image, while for the straight and curved waveguides the output signals are totally chaotic. Since the signal transmission in high-density photonic integration has always been the pursuit of people working in this field, this cascaded waveguide array suggests a strategy for high-density photonic integration.

3.

Experimental Results

In designing the experimental samples, each waveguide of the array is connected with two grating couplers (In and IIn) by taped waveguides from the two ends, where n represents the coupler number, n=6,5,0,5,6 [see Fig. 3(a)]. Therefore, it is easy to individually excite a particular waveguide in the input ports and analyze the propagation in the output ports. There are three samples (straight, curved, and cascaded waveguides) in the center with the same lengths of 40  μm. The designed parameters are d=0.7  μm, A=1  μm, and P=10  μm. The experimental samples are fabricated in a silicon wafer on a sapphire substrate using E-beam lithography with AR-N 7520 resists and an inductively coupled plasma etching process, which includes the waveguide array and extended grating couplers. The scanning electron microscopy (SEM) images of the fabricated devices are shown in Fig. 3(b). The coupling in and out processes are imaged by a near-infrared camera (Xeva-1.7-320) through a microscope objective.

Fig. 3

Experimental results. (a) Schematics of the experimental samples with three enlarged pictures showing three different waveguide arrays. (b) SEM images of the fabricated cascaded samples. (c)–(e) CCD recorded optical propagation from input (I0) to output through (c) straight, (d) curved, and (e) cascaded waveguide arrays. (f)–(j) Experimental results with different input port (II0, I6, I4, I1, and I6) for cascaded waveguide arrays. The bar diagrams in (c)–(j) in bottom panels display the extracted data of field intensity from output ports, where the input ports of signal are indicated by red arrows.

AP_2_3_036001_f003.png

In the experiments, we first input the light into the center waveguide by focusing the laser (λ=1450  nm) to the grating coupler (i.e., I0) for these three samples. The transmitted signals can be observed from another end of the grating coupler (i.e., IIn). Figures 3(c)3(e) show the charge-coupled device (CCD)-recorded optical propagation from input to output through the three samples, respectively. It is clear that there are bright spots from the expected output ports (II0) for the cascaded samples showing excellent imaging function. However, for cases of straight and curved samples, most of the optical field spreads into the side-lobes with little remaining at the center, definitely showing the discrete diffraction process. In addition, the spreading degrees of these two uniform samples are almost the same, indicating almost identical coupling strength despite different signs. In addition, we also input the light in the center grating coupler connected to the curved waveguides (i.e., II0) for the cascaded sample and observed the same result with bright spots in the expected output ports (I0) [see Fig. 3(f)], indicating a reciprocal imaging process.

To further demonstrate the imaging function, different input ports were illuminated in a controlled way, as for example shown in Figs. 3(g)3(j), for the input ports of I6, I4, I1, and I6, respectively. The bright spots from the expected output ports (II6, II4, II1, and II6) are evidently observed, revealing the exact high-quality point-to-point imaging process with no crosstalk to other output ports. It should be mentioned that, though the designed period is d=0.7  μm at wavelength of 1550 nm according to the simulations, the fabricated samples have a shrinking period to d0.64  μm due to fabrication imperfections, which causes a blueshift of the working wavelength (1450 nm). All imaging resolutions are beyond the diffraction limit (0.725  μm), and the superlens function of subdiffraction-limited imaging is well demonstrated in the experiments.

4.

Conclusion

We experimentally demonstrated optical self-imaging beyond the resolution limit in a 1-D silicon waveguide array. By connecting straight and curved waveguides, perfect self-imaging of an initial input state without crosstalk is realized in a high-density configuration. This design is implemented by tuning the coupling in the curved waveguides to be negative, mimicking the negative index material. Note that the subwavelength imaging can also be realized by plasmonics and metamaterials designs, such as plasmonic lenses36 and hyperlenses.37 Compared with these designs, our scheme has advantages in lower loss, easier fabrication requirements, and a naturally satisfied impedance matching condition. In principle, this coupled waveguide array system can be extended to a two-dimensional lattice to achieve a real imaging lens, though there would be more challenges in nanofabrications. Nevertheless, our approach provides a practical solution for efficient subwavelength self-imaging in on-chip optical signal routings, which is important in high-density photonic integrations.

Acknowledgments

The authors acknowledge the financial support from the National Key R&D Program of China (2017YFA0303701, 2016YFA0202103), National Natural Science Foundation of China (91850204, 11674167). Tao Li acknowledges support from Dengfeng Project B of Nanjing University. The authors have no conflicts of interest to disclose.

References

1. 

J. B. Pendry, “Negative refraction makes a perfect lens,” Phys. Rev. Lett., 85 3966 –3969 (2000). https://doi.org/10.1103/PhysRevLett.85.3966 PRLTAO 0031-9007 Google Scholar

2. 

M. C. K. Wiltshire et al., “Microstructured magnetic materials for RF flux guides in magnetic resonance imaging,” Science, 291 849 –851 (2001). https://doi.org/10.1126/science.291.5505.849 SCIEAS 0036-8075 Google Scholar

3. 

R. A. Shelby, D. R. Smith and S. Schultz, “Experimental verification of a negative index of refraction,” Science, 292 77 –79 (2001). https://doi.org/10.1126/science.1058847 SCIEAS 0036-8075 Google Scholar

4. 

A. Grbic and G. V. Eleftheriades, “Overcoming the diffraction limit with a planar left-handed transmission-line lens,” Phys. Rev. Lett., 92 117403 (2004). https://doi.org/10.1103/PhysRevLett.92.117403 PRLTAO 0031-9007 Google Scholar

5. 

D. R. Smith, J. B. Pendry and M. C. K. Wiltshire, “Metamaterials and negative refractive index,” Science, 305 788 –792 (2004). https://doi.org/10.1126/science.1096796 SCIEAS 0036-8075 Google Scholar

6. 

N. Fang et al., “Sub–diffraction-limited optical imaging with a silver superlens,” Science, 308 534 –537 (2005). https://doi.org/10.1126/science.1108759 SCIEAS 0036-8075 Google Scholar

7. 

W. Denk, J. Strickler and W. Webb, “Two-photon laser scanning fluorescence microscopy,” Science, 248 73 –76 (1990). https://doi.org/10.1126/science.2321027 SCIEAS 0036-8075 Google Scholar

8. 

S. W. Hell and J. Wichmann, “Breaking the diffraction resolution limit by stimulated emission: stimulated-emission-depletion fluorescence microscopy,” Opt. Lett., 19 780 –782 (1994). https://doi.org/10.1364/OL.19.000780 OPLEDP 0146-9592 Google Scholar

9. 

J. W. Lichtman and J.-A. Conchello, “Fluorescence microscopy,” Nat. Meth., 2 910 –919 (2005). https://doi.org/10.1038/nmeth817 1548-7091 Google Scholar

10. 

B. Huang, M. Bates and X. Zhuang, “Super-resolution fluorescence microscopy,” Ann. Rev. Biochem., 78 993 –1016 (2009). https://doi.org/10.1146/annurev.biochem.77.061906.092014 ARBOAW 0066-4154 Google Scholar

11. 

M. G. L. Gustafsson, “Surpassing the lateral resolution limit by a factor of two using structured illumination microscopy,” J. Microsc., 198 82 –87 (2000). https://doi.org/10.1046/j.1365-2818.2000.00710.x JMICAR 0022-2720 Google Scholar

12. 

L. Schermelleh et al., “Sub-diffraction multicolor imaging of the nuclear periphery with 3D structured illumination microscopy,” Science, 320 1332 –1336 (2008). https://doi.org/10.1126/science.1156947 SCIEAS 0036-8075 Google Scholar

13. 

R. Fiolka et al., “Time-lapse two-color 3D imaging of live cells with doubled resolution using structured illumination,” Proc. Natl. Acad. Sci. U. S. A., 109 5311 –5315 (2012). https://doi.org/10.1073/pnas.1119262109 Google Scholar

14. 

D. R. Smith and D. Schurig, “Electromagnetic wave propagation in media with indefinite permittivity and permeability tensors,” Phys. Rev. Lett., 90 077405 – (2003). https://doi.org/10.1103/PhysRevLett.90.077405 PRLTAO 0031-9007 Google Scholar

15. 

A. Poddubny et al., “Hyperbolic metamaterials,” Nat. Photonics, 7 948 –957 (2013). https://doi.org/10.1038/nphoton.2013.243 NPAHBY 1749-4885 Google Scholar

16. 

J. Yao et al., “Optical negative refraction in bulk metamaterials of nanowires,” Science, 321 930 – (2008). https://doi.org/10.1126/science.1157566 SCIEAS 0036-8075 Google Scholar

17. 

I. I. Smolyaninov, Y.-J. Hung and C. C. Davis, “Magnifying superlens in the visible frequency range,” Science, 315 1699 –1701 (2007). https://doi.org/10.1126/science.1138746 SCIEAS 0036-8075 Google Scholar

18. 

Z. Liu et al., “Far-field optical hyperlens magnifying sub-diffraction-limited objects,” Science, 315 1686 (2007). https://doi.org/10.1126/science.1137368 SCIEAS 0036-8075 Google Scholar

19. 

J. Rho et al., “Spherical hyperlens for two-dimensional sub-diffractional imaging at visible frequencies,” Nat. Commun., 1 143 (2010). https://doi.org/10.1038/ncomms1148 NCAOBW 2041-1723 Google Scholar

20. 

D. N. Christodoulides, F. Lederer and Y. Silberberg, “Discretizing light behaviour in linear and nonlinear waveguide lattices,” Nature, 424 817 –823 (2003). https://doi.org/10.1038/nature01936 Google Scholar

21. 

L. Verslegers et al., “Deep-subwavelength focusing and steering of light in an aperiodic metallic waveguide array,” Phys. Rev. Lett., 103 033902 (2009). https://doi.org/10.1103/PhysRevLett.103.033902 PRLTAO 0031-9007 Google Scholar

22. 

Y. Liu and X. Zhang, “Metasurfaces for manipulating surface plasmons,” Appl. Phys. Lett., 103 141101 (2013). https://doi.org/10.1063/1.4821444 APPLAB 0003-6951 Google Scholar

23. 

E. Verhagen, “Three-dimensional negative index of refraction at optical frequencies by coupling plasmonic waveguides,” Phys. Rev. Lett., 105 223901 (2012). https://doi.org/10.1103/PhysRevLett.105.223901 PRLTAO 0031-9007 Google Scholar

24. 

U. Peschel, T. Pertsch and F. Lederer, “Optical Bloch oscillations in waveguide arrays,” Opt. Lett., 23 1701 –1703 (1998). https://doi.org/10.1364/OL.23.001701 OPLEDP 0146-9592 Google Scholar

25. 

R. Iwanow et al., “Discrete Talbot effect in waveguide arrays,” Phys. Rev. Lett., 95 053902 (2005). https://doi.org/10.1103/PhysRevLett.95.053902 PRLTAO 0031-9007 Google Scholar

26. 

S. Longhi et al., “Observation of dynamic localization in periodically curved waveguide arrays,” Phys. Rev. Lett., 96 243901 (2006). https://doi.org/10.1103/PhysRevLett.96.243901 PRLTAO 0031-9007 Google Scholar

27. 

S. Longhi, “Image reconstruction in segmented waveguide arrays,” Opt. Lett., 33 473 –475 (2008). https://doi.org/10.1364/OL.33.000473 OPLEDP 0146-9592 Google Scholar

28. 

A. Szameit et al., “Image reconstruction in segmented femtosecond laser-written waveguide arrays,” Appl. Phys. Lett., 93 181109 (2008). https://doi.org/10.1063/1.2999624 APPLAB 0003-6951 Google Scholar

29. 

A. Szameit et al., “Inhibition of light tunneling in waveguide arrays,” Phys. Rev. Lett., 102 153901 (2009). https://doi.org/10.1103/PhysRevLett.102.153901 PRLTAO 0031-9007 Google Scholar

30. 

W. Song et al., “Breakup and recovery of topological zero modes in finite non-Hermitian optical lattices,” Phys. Rev. Lett., 123 165701 (2019). https://doi.org/10.1103/PhysRevLett.123.165701 PRLTAO 0031-9007 Google Scholar

31. 

B. Xu, T. Li and S. Zhu, “Simulation of massless Dirac dynamics in plasmonic waveguide arrays,” Opt. Express, 26 13416 –13424 (2018). https://doi.org/10.1364/OE.26.013416 OPEXFF 1094-4087 Google Scholar

32. 

S. Longhi, “Quantum-optical analogies using photonic structures,” Laser Photonics Rev., 3 243 –261 (2008). https://doi.org/10.1002/lpor.200810055 Google Scholar

33. 

J. M. Zeuner et al., “Optical analogues for massless Dirac particles and conical diffraction in one dimension,” Phys. Rev. Lett., 109 023602 (2012). https://doi.org/10.1103/PhysRevLett.109.023602 PRLTAO 0031-9007 Google Scholar

34. 

W. Song et al., “High-density waveguide superlattices with low crosstalk,” Nat. Commun., 6 7027 (2015). https://doi.org/10.1038/ncomms8027 NCAOBW 2041-1723 Google Scholar

35. 

R. Gatdula et al., “Guiding light in bent waveguide superlattices with low crosstalk,” Optica, 6 585 –591 (2019). https://doi.org/10.1364/OPTICA.6.000585 Google Scholar

36. 

Z. Liu et al., “Focusing surface plasmons with a plasmonic lens,” Nano Lett., 5 1726 –1729 (2005). https://doi.org/10.1021/nl051013j NALEFD 1530-6984 Google Scholar

37. 

D. Lu and Z. Liu, “Hyperlenses and metalenses for far-field super-resolution imaging,” Nat. Commun., 3 1205 (2012). https://doi.org/10.1038/ncomms2176 NCAOBW 2041-1723 Google Scholar

Biography

Wange Song is a PhD student working under the supervision of Tao Li at the College of Engineering and Applied Sciences at Nanjing University. He received his BS degree from Nanjing University in 2016. Currently, he is working on topological and waveguide array physics.

Hanmeng Li is a PhD student working under the supervision of Tao Li at the College of Engineering and Applied Sciences at Nanjing University. He is currently working on metasurfaces and nanofabrication.

Shenglun Gao is a master student working under the supervision of Tao Li at the College of Engineering and Applied Sciences at Nanjing University. He is currently working on nanofabrication.

Chen Chen is a PhD student working under the supervision of Tao Li at the College of Engineering and Applied Sciences at Nanjing University. She received her BS degree from Nanjing University in 2016. Currently, she is working on metasurface devices.

Shining Zhu is a professor at Nanjing University. He received his PhD at Nanjing University in 1996. He is the group leader of Dielectric Superlattice Laboratory. His research interests include condensed matter optics, quasi-phase matching physics and nonlinear optics, optoelectronic functional materials, quantum optics, and metamaterials.

Tao Li is a professor at the College of Engineering and Applied Sciences in Nanjing University. He received his PhD from Nanjing University in 2005. His research interests include metamaterials, plasmonics, and nanophotonic integrations.

CC BY: © The Authors. Published by SPIE under a Creative Commons Attribution 4.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.
Wan-ge Song, Hanmeng Li, Shenglun Gao, Chen Chen, Shining Zhu, and Tao Li "Subwavelength self-imaging in cascaded waveguide arrays," Advanced Photonics 2(3), 036001 (12 May 2020). https://doi.org/10.1117/1.AP.2.3.036001
Received: 14 February 2020; Accepted: 23 April 2020; Published: 12 May 2020
Lens.org Logo
CITATIONS
Cited by 28 scholarly publications.
Advertisement
Advertisement
KEYWORDS
Waveguides

Silicon

Dispersion

Metamaterials

Diffraction

Integrated optics

Wave propagation

Back to Top